Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Miura, Yukitoshi; Hoshino, Katsumichi; Kusama, Yoshinori
Purazuma, Kaku Yugo Gakkai-Shi, 80(8), p.653 - 661, 2004/08
A series of experimental program on the JAERI Fusion Torus-2M (JFT-2M) was completed in March, 2004. In the experimental operation for 21 years since the first plasma on April 27, 1983, many significant results leading the fusion energy research and plasma physics have been produced in researches on high confinement mode (H-mode), heating and current drive, advanced plasma control, compatibility of low activation ferritic steel with improved confinement mode, etc. Among these results, some important results are presented.
Furuya, Kazuyuki; Wakai, Eiichi; Ando, Masami; Sawai, Tomotsugu; Iwabuchi, Akira*; Nakamura, Kazuyuki; Takeuchi, Hiroshi
Fusion Engineering and Design, 69(1-4), p.385 - 389, 2003/09
Times Cited Count：23 Percentile：80.7(Nuclear Science & Technology)In a fusion reactor, a blanket made of a low activation material like F82H is fabricated by solid Hot Isostatic pressing (HIP) joining method. In a previous study, blanket, grain coarsenings were found in a mock-up around HIP-joined region. To verify an effect of the coarsenings on a strength of the HIP-joined region, tensile test and hardness measurement were done. As the results, the tensile strength increased by about 50 MPa, and the elongation decreased by about 4 % in comparison with that of a standard alloy. Though the hardness was almost constant both in the coarsening and a non-coarsening regions, both of these hardness increased by about 5 %. Therefore, it could be judged that change of the tensile property is due to increase of the hardness. On the other hand, tensile and impact tests of a base metal without coarsening resulted in DBTT increase by about 40 K, although the tensile property was nearly equal to that of the joined-region with coarsening. It can be understood that this is the effect of the heat treatments in the fabrication process of the mock-up.
Urata, Kazuhiro*
JAERI-Data/Code 2003-005, 36 Pages, 2003/03
JAERI-Data-Code-2003-005.pdf:2.96MB
In design of the fusion devises in which ferritic steel is planned to use as the plasma facing material and/or the inserts for ripple reduction, the appreciation of the error field effect and the optimization of ferritic plate arrangement to reduce the toroidal field ripple require calculation of ferritic magnetic field. However iterative calculations by the non-linearity in B-H curve disturbs high-speed calculation. In the strong toroidal magnetic field in the tokamak, fully magnetic saturation of ferritic steel occurs. Hence a distribution of magnetic charges as magnetic field source is determined straightforward. Additionally objective ferritic steel geometry is limited to the thin plate and they are installed along the toroidal magnetic field. Taking them into account, high-speed calculation code FEMAG has been developed. In this report, the formalization of FEMAG, how to use FEMAG, and the validity check in comparison with a 3D FEM code, with the measurements of the magnetic field in JFT-2M are described. The presented examples are design studies for JT-60 modification.
Jitsukawa, Shiro; Tamura, Manabu*; Van der Schaaf, B.*; Klueh, R. L.*; Alamo, A.*; Petersen, C.*; Schirra, M.*; Spaetig, P.*; Odette, G. R.*; Tavassoli, A. A.*; et al.
Journal of Nuclear Materials, 307-311(Part1), p.179 - 186, 2002/12
Times Cited Count：160 Percentile：99.28(Materials Science, Multidisciplinary)Reduced activation ferritic/martensitic steel is the primary candidate structural material for ITER Test Blanket Modules and DEMOnstration fusion reactor because of its excellent dimensional stability under irradiation and lower residual activity as compared with the Ni bearing steels such as the austenitic stainless steels. In this paper, microstructural features, tensile, fracture toughness, creep and fatigue properties of a reduced activation martensitic steel F82H (8Cr-2W-0.04Ta-0.1C) are reported before and after irradiation, in addition to the design concept used for development of this alloy. A large number of collaborative test results including those generated under the IEA working group implementing agreements are collected and are used to evaluate the feasibility of use of F82H steel as one of the reference alloys. The effect of metallurgical variables on the irradiation hardening is reviewed and compared with the results obtained from irradiation experiments.
